Furnace Structure |
- Double layer steel casing with air cooling keeps furnace surface temperature lower than 60°C.
- High purity fibrous alumina insulation for maximum energy saving.
- Split cover with Interlock protection, cut the power if lid open during furnace heating process.
|
Power Input |
208-240 AC, 50/60 Hz single phase, 9 KW Max. (60A breaker required) |
Heating Elements |
- 8 pcs 1Kw Halogen light tube, ( Dia. =10mm, L=300mm, Heated Length =200mm)
- Standard working life: 2000 hrs. ( depends on heating rate )
- The Halogen light tube is consumable. Please click picture left to order spare one
|
Heating Zone |
12″ length with 4″ constant temperature zone within +/-5ºC uniformity |
Working Temperature |
- 1100ºC Max. for < 10 minutes
- 1000ºC Max. for < 20 minutes (Note: if running longer time, furnace case will > 100oC, must use fan cooling case from outside )
- 800ºC Max. for < 120 minutes
- 600ºC Max. for Continuous
|
Max. Heating Rate |
50ºC/sec |
Cooling Rate |
- Max. Cooling: 60ºC/min (Under vacuum: 200 mtorr), 117ºC/min (under atmospheric pressure)
- Lowest Cooling: 10 ºC / minute
|
Thermocouple |
K type, the head of the thermocouple touches the Aluminum Nitride sample holder from underneath |
Temperature Controller |
- temperature controller is included.
- Proportional–integral–derivative control (PID control) and auto-tune function
- 30 segments programmed with ramping, cooling and dwelling steps
- Built-in over-temperature alarm and thermocouple failure alarm
- +/- 1 ºC temperature control accuracy
- Default DB9 PC communication port
- MET Certified
|
Temperature controller (optional) |
- MTS02-Y Temperature control software kit (for YD518P series controllers) + 15″ laptop package is available at the options bar.
- You may upgrade the temperature controller to the Eurotherm 3504 Temperature Controller which is fully compatible with LabVIEW. This package includes a Eurotherm 3504 programmer, a communication cable (RS485 – USB) and a software CD. Click the pic below to view the full spec of Eurotherm 3504 temperature controller.
|
Quartz Tube & Sample Holder |
- Quart Tube Size: 4.33″ O.D x 4.05″ I.D x 16.2″ Length. One 3″ Diameter AlN sample holder for annealing samples up to 3″ Dia is included. AlN has a very high thermal conductivity which provides the best temperature uniformity in the sample area.
- Optional: 3” O.D Thick Graphite Substrate can be used as an alternative to AIN plate. (please click pic-3 below to order)
- Optional: Graphite Crucible:87 mm OD x 71 mm ID x 12 mm Height with lid is designed for 3″ sample holder, can also be modified into an RTE, CSS or HPCVD furnace with a graphite crucible coated with SiC.
- The sample holder is removable from the flange for using the RTP furnace for other purposes.
|
Vacuum Flange |
- KF-D25 High Vacuum Flange is made of stainless steel with double hi-temp. silicone O-rings, needle valves, and water cooling jacket.
- Only requires water cooling in long running times at temperatures > 600oC.
- Circulating water rate: 0.5 m3 /hr.
- The slide-out flange provides an easier way of loading, unloading the samples and other specific process needed.
- Insert-able thermal-couple for accurate measurement.
|
Vacuum Pump (optional) |
- EQ-FYP vacuum pump is recommended for this furnace. The ultimate vacuum pressure in this system can be 10^-3 torr. Vacuum bellows and clamps are included in this package. Click here for the spec of EQ-FYP vacuum pump.
|
Water Cooling (optional) |
- Cooling water is required.
- Please make sure the flow rate of cooling water is ≥ 10L/min, water temp. < 25ºC; pressure > 25 PSI.
- We suggest using the EQ-KJ5000 Series recirculating water chiller as a cooling system (please order separately at related products below) to save water.
- Warning: This RTP furnace’s max dwelling time shall be less than 600 seconds at 1000ºC ~ 1100ºC with tap water, otherwise O-ring may melt.
|
Flow-meter |
One flow meter is installed on the front panel for adjusting gas flow from 16 – 160 ml/min |
Vacuum Gauge |
Digital vacuum gauge with a measurement range from 10-4 to 1000 Torr is installed on the furnace. |
Vacuum Pressure & Gas Fitting |
- Pressure can reach 50 mtorr by using mechanical vacuum pump with KF25 adapter
- Pressure can reach 10-4 torr by molecular pump with KF25 adapter
|
Dimensions |
- Flange closed: 760mm(L) X 330mm(W) X 530mm(H) /Flange opened: 1200mm(L) X 330mm(W) X 530mm(H)
|
Net Weight |
70 kg (150 lbs) |
Warranty |
One year limited manufacturer warranty with lifetime support (Consumable parts such as processing tubes, o-rings and halogen lamps are not covered by the warranty, please order replacements at related products below). |
Laptop, software & WiFi Control(Optional) |
- Brand new laptop with Microsoft Window 10 and Microsoft Office 2013 (30 days free trial) for immediate use.
- Labview Based Temperature Control System) enables user to edit temperature profile, manage heat-treatment recipe, record and plot data for MTI furnaces.
- A wireless remote control provides up to 300 meters operating range.
- Above features are available upon request at an extra cost (up to $1,000). Please contact us for more information.
- Note:
The software is only compatible with MTI’s Yudian Temperature Controller
|
Compliance |
Please select the certificate in options bar:
CE Certificate & UL/CSA ready: CE approval, ready to pass UL/CSA certificate
UL certircate – UL apprval (UL 61010), at extra cost |
Optional |
- You may combine the RTP furnace with high vacuum station or gas livery system as vacuum furnace or CVD system. Click pictures below to see details
- For achieving fast cooling rate (< 10ºC/second), you may choose RTP furnace with sliding rail. Please click the picture below to see details.
- You may order pressure control module.
|
Application Notes
|
- Tube furnaces with quartz tubes are designed for using under vacuum and low pressure < 0.2 bars / 3 psi / 0.02 MPa. Vacuum pressures may only be safely used up to 1000°CThe flow rate for gasses should be limited to<200 SCCM (or 200ml/min) for reducing thermal shocks to the tube
- Attention: A two-stage pressure regulator must be installed on the gas cylinder to limit the pressure to below 3 PSI for safe operation. This furnace also can be modified into an RTE, CSS or HPCVD furnace with a graphite crucible coated with SiC ( click Pic-left for detail how to set up an RTE processing by DIY )
- After CVD, the graphene must be transferred from the metal catalyst to another substrate for most applications. By using the graphene transfer tape, the residue can be low.
|
There are no reviews yet.